Crazyflie Nano Quadcopter 10 DOF Kit

1 reviews  (4/5 ) 1 reviews  •  Write a review
Product Code: 91350
Availability: In Stock Views: 21740
DeliverySame Day Delivery
Product Description
  • Small and lightweight, around 19g and about 90mm motor to motor
  • Flight time up to 7 minutes
  • ~20min charge time
  • Up to 80m range when using the Crazyradio USB dongle
  • 3-axis high-performance MEMs gyros with 3-axis accelerometer
  • 3-axis magnetometer (compass)
  • High precision altimeter
  • 4-layer low-noise PCB design with separate voltage regulators for digital and analog supply
$200.00
Qty: Add to Cart

Shipping Options to United States

Select Country:
* Region / State:

Crazyflie Nano Quadcopter 10 DOF Kit info

The Crazyflie Nano Quadcopter is one of the tiniest quadcopters which is 9 cm long and weighs only about 19 grams. Basically, it fits in your hand! The Crazyflie Nano Quadcopter can be used for entertainment by hobbyists, but it is mainly used as a development platform which can be used to experiment, develop and explore. Since it’s very small it is perfect for develoing new software and can easily be flown indoors. The quadcopter is able to lift a load up to 10 gr.

One of the main advantages of the Crazyflie Nano Quadcopter Kit is that its development platform is open source. The schematics and firmware/host source code is accessible via the developer website and the wiki. Developers can start by using the details and information on how to set up the development environment.

The 10 DOF version of Crazyflie has extra sesors for altitude and heading angle measurements. Although there is no firmware support for these sensors, they can be used to control heading angle and altitude. For developers who would like to develop a new algorithm or for hobbyists who would like to use some advanced algorithm, the 10 DOF version would be much more useful.

The Crazyflie Nano Quadcopter can be controlled by connecting to a PC or to another host which supports USB Host or OTG (like Android devices). The connection to PC is supported by Windows and Linux. Mac OSX has no official support, but it is handled by the community. The control of the quadcopter by the host is carried on by an integrated 2.4GHz radio chip which is used for receiving commands and sending telemetry data to the host. The communication with the host is handled by the Crazyradio 2.4 GHz USB radio dongle.

The Crazyflie Nano Quadcopter can be wirelessly programmed via a radio bootloader from a host PC. JTAG is not strictly needed to program the quadcopter, but for advanced development and debugging there is also an accessible JTAG interface. Note that the quadcopter is pre-programmed and programming it using a host PC is not a requirement.

 

Crazyflie Nano Quadcopter 10 DOF Kit - General Specifications

The Crazyflie Nano Quadcopter features:

  • Small and lightweight, around 19g and about 90mm motor to motor
  • Flight time up to 7 minutes with Standard 170mAh Li-Po battery
  • Standard micro-USB connector for charging which takes ~20min for the stock 170mAh Li-Po battery
  • On-board low-energy radio@1mW based on the nRF24L01+ chip. Up to 80m range (environment dependent) when using the Crazyradio USB dongle
  • Powerful 32-Bit MCU: STM32F103B @ 72 MHz (128 kb flash, 20 kb RAM)
  • 3-axis high-performance MEMs gyros with 3-axis accelerometer: Invensense MPU-6050
  • 3-axis magnetometer HMC5883L (compass)
  • High precision altimeter MS5611-01BA03
  • Expansion header 2x10 pins 1.27mm (0.05”) pitch including power , I2C/UART, SPI/ADC. Header also contains ARM Cortex 10-pin JTAG (header not included)
  • 4-layer low-noise PCB design with separate voltage regulators for digital and analog supply

 

Crazyflie Nano Quadcopter 10 DOF Kit - Technical Specifications

The Crazyflie Nano Quadcopter 10 DOF Kit includes

  • 1 x Crazyflie control board
  • 5 x Motor mounts
  • 5 x Coreless DC motors
  • 5 x CW propeller
  • 5 x CCW propeller
  • 1 x LiPo battery
  • 1 x 2*5 pins 1.27mm (0.05”) pitch header

The Crazyflie Nano Quadcopter 10 DOF Kit does not include but requires for flying

  • A Standard micro-USB cable for charging
  • A PC compatible joystick
  • A PC
  • A Crazyradio

To assemble the CrazyFlie Nano Quadcopter you need

  • A soldering iron
  • Solder

 

Video

 

 

Resources

Download Windows Driver

Bitcraze Websitehttp://www.bitcraze.se/crazyflie/

Bitcraze Wikihttp://wiki.bitcraze.se/

 

Crazyflie Logging and Parameter Framework Tutorial

 

on
4 ( 4 / 5 )
Güzel bir ürün, bence denemelisiniz.
Write a review Your Name:


Your Review:Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below: